TensorGrip L20

TensorGrip L20

TensorGrip L20 is suitable for bonding HPL, hard plastics, GRP, foams and fabrics to a variety of substrates including MDF, chipboard, plywood and many other timber sheet materials. TensorGrip L20 is designed for permanent bonding of materials where immediate bond strength, water resistance and high heat resistance are required. L20 can also be used for bonding sheet metals, where surface preparation is very important – surface must be degreased and lightly abraded with fine abrasive or non- woven material.

ALWAYS test TensorGrip L20 to determine suitability for your particular application prior to use in production. NOT RECOMMENDED for use with plasticised vinyls, flexible plastics, expanded/extruded polystyrene, PE or PP.

As part of our WOODWORKING range, L20 is a web spray adhesive designed for use in fabricating countertops, cabinets and doors using the substrates listed above.

 

TensorGrip L20 Benifits

  • Fast Drying
  • Good Heat Resistance
  • Very High Solids
  • Portable Systems
  • Non-Chlorinated Adhesive
  • Easy Application Control
  • LEED Compliant
  • Halogen Free

 

TensorGrip L20 Directions For Use

  • This product is designed to be applied to two surfaces to be bonded together. Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. For best results, the temperature of the adhesive and the surfaces being bonded should be between 60 degrees F – 80 degrees F (16degrees C – 27 degrees C)
  • Use with adequate ventilation. When possible we recommend shaking the canister well before using. Attach and secure hose tightly onto the spray gun with required tip. Attach the other end of the hose onto the canister. Make sure the hose-valve connections are securely tight. Open the valve on the canister slowly and fully, check for leaks during this process. Unlock the trigger on the spray gun to start spraying.
  • Prior to use, Check compatibility by spraying a small test patch of the adhesive on the substrate. This product may degrade some substrates. Spray about 10-20 cm (4” – 8”) away at a 90 degree angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of adhesive in areas that appear to need more adhesive. Spray both surfaces to be bonded, one surface vertically and the other surface horizontally. Allow the adhesive to tack off until no adhesive transfers to the knuckle when touched.
  • Adhere surfaces and press together with adequate pressure. A roller is recommended to apply a uniform pressure to achieve maximum strength. Allow 24 hours for the adhesive to fully cure.
  • If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice.

 

TensorGrip L20 Canister Storage/Change Over

  • Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister. Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean. If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open. Do not disconnect the hose/gun from the canister. Close and lock the spray gun.

Terms of Sale

  • There are no refunds or exchanges for this product.
  • We no longer ship to residential addresses.
  • Free freight applies to metro zones only.
  • Customers must download and read through the available MSDS documents 

Ordering

SKU OA-TG-L20 Categories , ,

$422.00$3,761.00 Ex GST

Spray Guide

Brochure

MSDS

TDS

Tip Guide

Cleaning

You may also be interested in...